How to knit a knitted knitting needle?

When a beginner needlewoman for the first timecollides with knitting, she has a lot of questions. For example, how to choose yarn, tools, where to start. More experienced craftsmen are interested in learning how to get knitted with knitting needles. All these questions will be raised in the article presented.

How to start a newbie?

It is clear that an experienced needlewoman will nottell your budding girlfriend what nakid is with knitting needles, how to knit it and why it is needed. Perhaps, it can be left for later. To say which thing to knit first, is quite difficult. Each needlewoman has a different level of skill, patience, attentiveness and accuracy. It is very important that the first experience in knitting does not cause any irritation at all, otherwise the desire to engage in such a craft will disappear for a long time.

It is recommended to study the special literature,read master classes for beginners, consult a person who is engaged in needlework for a while. In any case, you have to practice a little hitching, learn to knit the front and back, close the series and only then go to more complex patterns. The first thing that can be made with knitting needles can be a simple scarf, a jumper or a pillow case. It's important to start, get pleasure from it and develop your skills.

Choice of yarn

When knitting, it is important to select the correct thread. For spokes, yarn of any thickness and with different components will suit. It is advisable to buy more threads than indicated in the scheme. This is due to the fact that each pattern will require a different amount of yarn, so to anticipate the expense is quite difficult.

When choosing a consumable it is important to drawattention to the twisting of threads. If they are too tightly woven, then the stocking can be slightly mowed. To check this, you need to unwind a piece of 100 cm long thread, put the beginning and the end together. If the loop lazily twists 2-3 times, then the canvas, connected with a stocking pattern, will not mow. If the thread is vigorously folded more than 10 times, then such a yarn should not be chosen for such a rapport, in order to avoid distortion. Perhaps, if one of the components of the pattern is knitted with knitting needles, then it will be possible to avoid such a problem.

Also, the yarn should be checked for resistance tocoloration. To do this, take a piece of white fabric, fold it into a roll, on top of which the required thread (20-30 cm) is wound. So you can do with all the samples of yarn that will participate in knitting. Rolls of fabric should be washed and dried in a folded state. Then you need to unwind the threads and make sure that they do not leave any traces after washing.

Selection of knitting needles

Knitting needles (knitting needles) for knitting can be divided into two categories: by shape and by material.

In form this tool is divided into:

circular (circular);
direct.

The main materials for making knitting needles are:

metal (aluminum, steel, duralumin);
plastic;
bamboo;
tree;
bone.

The toolkit should not be rough. Its surface should not contain a notch, as this will interfere with knitting. Create a variety of patterns with knitting needles on any tool. The main thing is that the thread slips easily and without difficulty.

All spokes are divided into numbers from 1 to 20. According to the experts, it is rather difficult to work with thick tools because of the fast-onset fatigue of the hands.

In addition to the spokes, additional elements are used in the work:

vintage loops;
short curved spokes;
Loop holders or pins to remove unclosed stitches;
counters of rows;
caps for long spokes.

Preparing yarn for work

In order to make the canvas beautiful, andsome elements, for example, nakid knitting, at work did not cause difficulties, craftsmen prepare yarn. It is important to do it correctly, to rewind the consumables in the morning. It is desirable to wash the threads, dry them and roll them into a ball. What is this for? In order to determine during the processing how the thread will behave: it will stretch, deform or shrink. After washing and drying, the thread will not produce undesirable results during the socks.

It is most convenient to work when the yarn is wound on a bobbin or a Bulgarian tangle. It is recommended to pull the thread from inside the skein.

If the yarn from one coil is over, thenIt is recommended not to tie the end of the old reel to the knot and start a new one, but to lay one on top of the other and tie together several loops. To avoid thickening in this case, skilled craftsmen advise to untwist the endings of threads and only then to superimpose one on another. After the item has been created on the wrong side, the "traces" data should be attached.

Loosening of the front and back loops

Finally the conversation approached the immediate beginning of the work. Before you make any product, you need to know how to perform the front and back, removed and extended hinges, nakid spokes.

After the beginning needlewomanprepared the original series, she should take off the first stitch and do not tie. The thread is located on the index finger of the left hand. The right needle is inserted into the second loop, grasps the yarn, pulls it through the stitch, which immediately descends from the left stocking needle. It turns out that the newly appeared element remains on the right side. Similarly, you should knit to the end of the row.

Advice from experienced craftsmen: Do not tighten the hinges too tightly. It is better if the mating is medium density. Tight loops are difficult to pull. And too loose stitches look ugly on the finished canvas.

In case of wrong weaving the working thread is putbefore the canvas on the index finger. The right knitting needle is inserted from the back side into the second stitch (the first is removed), yarn is grasped. With the help of the index finger of the working arm, it is necessary to stretch the thread through the loop and leave it on the main stocking needle. The series is fully extricated.

Closing loops

To prevent the canvas from blooming, it is necessary to close the working loops after finishing work on it. There are 2 common ways of fixing stitches:

To knit together 2 loops according to the drawing. One stitch is obtained, which goes to the previous spoke. By circulating 2 loops together and leaving the resulting new element to the left, the master will close the entire row completely.
It is necessary to remove the edge loop. Next, tie a pattern. The left spoke to pass over the resulting stitch on the right side to the edge, grab it. With the right stocking needle, stretch a second loop through it and leave it in its original position.

The next stitch should be patterned. Repeat the actions to "capture" the first loop and return it to the left spoke. By making such alternate manipulations with stitches, the needlewoman can close the entire row. It does not matter, if in the last row there was a facial mantle, it will be possible to fasten the hinges with knitting needles without damage to the knitted fabric.

Catching the crochet

After gaining the skills to create facial andthe stitcher passes to the next stage. Now a beginner skilled worker will understand how to make a knitted knitting needles and tie a unique pattern. Typically, similar techniques are used to create a delicate and patent pattern, a cloth with elongated stitches and a complex weave of threads.

There are such loops "to themselves" and "from themselves":

Reverse cape. In another way, it is called "to yourself." In this case, it is necessary to pass the end of the main knitting needle under the working thread and grab the yarn from the right to the left.
Direct nakid. Otherwise, it is called "from itself." The end of the main knitting needles pass over the working thread and, moving from left to right, throw the yarn into a loop.

The face stitch is very easy to do with such manipulations. The purl is necessary to hold the finger, so that the loop does not jump off in the process.

How to knit knit loop is easy to understand. The main thing is to work out this technique in practice.