How to knit socks on 5 spokes: you can learn if you want

Often I want to make my family membersA small gift, connecting them something. In the cold season, such a gift will be warm socks that warm them in the winter. In addition, they will remind their relatives that they are loved and taken care of. How to knit socks on 5 spokes, so they turned out comfortable and beautiful? Let's look at this article.

How to knit socks on 5 spokes? Let's see what's what for

Knitting Pattern Knitting on five spokes provides for its creation without a single seam. Work on the product will be done spirally. And at its end, the thing will fit perfectly on the leg.

How to knit socks on 5 spokes? Is it difficult? Not at all. They are knitted circular viscous from above the toe to the toe. Necessary loops are typed on four spokes, and the fifth - will be working.

The number of loops should be calculated, focusing on the circumference of the leg. It is necessary to remove two of its measures:

The first is the circle of ascent. It is only necessary to measure the foot from the heel to the ascent along the inclined plane. The measurement is carried out in the usual centimeter.

The second is the circumference of the foot itself. This measure is determined at the foot, where the thinnest place of the leg is located, above the stone.

Now that all the measurements have been taken out, it is necessary to determine the middle circle: to add the circumference of the lift and the circumference of the leg and divide the resulting digit by two.

For example, let's take the size of the circle of lifting -31 cm, and the circumference of the leg - 21 cm. Summing 31 and 21, we get 52, and 52 divide by two, it turns out 26 cm. It is this number of centimeters and will be the same, according to which the loop set calculation should be done. It is best that the resulting number of loops be rounded to a number that can be divided into four. This is done so that the loops can be conveniently divided into four spokes.

Constant

We learn how to knit socks on 5 spokes. You need to type the number of loops you need to work. Then - distribute them to four spokes. And to untie the rubber band circular viscous. Typically, the length of the rubber is five to six centimeters, but in fact, it is slightly more or slightly less - which of the knitters as they want. After this, you need to tie about seven centimeters to a heel of viscous viscous. Pjatochku knit, using two spokes and half loops. But the second half should remain on the spokes, which at the moment in knitting do not participate.

Using two eyelets, one must associate the usuallinen viscous viscous - from five and a half to six centimeters. This will be the height of the heel. Depending on what kind of lifting of the foot, it can be a bit smaller. If viewed from the 35th foot size - the height will be a constant value. The knitting pattern of the sock gives a detailed description of each action of the wizard.

Now, to give shape to the heel, one must dodescent. This is done in this way: all the loops should be divided into three parts. If you get extra loops, they can be attached to the part located in the center (this, if the number of loops can not be divided into three). The further actions are as follows: the loops relating to the central part must be knit further, but the loops that refer to the side parts (namely, the sides of the heel will be made of them) will later join in little by little to the central loop.

Turn back and forth

How to knit socks on 5 spokes? Just read this article carefully. At this stage, you can start from the inside of the lowering of the loops, and it ends on the front side. Two-thirds of the loops should be sewn with the purlins, then two loops together - the last loop from the part in the center, and the first loop from the third part - they must be sewn together with the back.

Now you have to turn your knitting and tie on the front side of the heel. It is necessary to pay attention to the fact that the first eyelet should be removed at this turn, but it is not necessary to tie it.

Now goes knitting with the eyelets of the lastthe loop of the part located in the center, and the first loop of the first part must be tied together with a broach (the first loop should be removed, and the next - to be tied with the front one, and then the removed loop is transferred to the knitted). And again you need to turn the knitting, remove the first loop, not tying it, and so on.

Knitting in a circle

Next, you need to continue knitting, until all the lateralthe loops will not be closed. Now you need to get a loop from the side of the heel. From the two rows you need to type three loops, that is, from each second row you need to type one loop and one additional loop. That's how socks are made. The description of knitting gives detailed information about what and how to do.

You can switch to knitting in a circle. In the work come the eyelets from the spokes, which were laid off earlier, again typed loops from the side parts of the heel and the loops of the heel part located in the center. It is necessary to tie one row with the help of facial mating. Now in every second circular ryadochke for the heel to fit as best as possible, it is necessary to tie the third and second eyelets from the end of the first knitting needle at once with the eyelet and the second and third eyelets of the fourth knitting needle simultaneously.

From decreasing to the end of work

Now it is necessary to do the reductions untilneed not count the initial number of loops (that is, the same number as it was typed before starting work). And you can begin to knit a foot, performing it with a facial knitting. Work goes in a circle - either to the tip of the little finger, or to the bone of the thumb. After that you need to loosen the toe of the sock.

Loops need to be reduced correctly. This is done in this way: in each second row, the third and second loops from the end of the first and third spokes are tied together with the eyelets. And the second and third eyelets with the second and fourth spokes - tie together drawing.

Gradually, only half remains on the knitting needlesloops. These decreases must be carried out in each circular ryadochke, up to the last four loops. They need to be tightened and fixed. That's how knitting of men's socks ends.