Repair and replacement of locks in metal doors

Recently, metal doors are in great demand. Someone establishes them in order to protect their home from hacking, and someone - in order to create an aesthetic appearance.

Repair and replacement of locks in metal doors

Of course, it's beautiful and reliable enough. But sometimes it is necessary to replace the locks in the metal door. Various reasons can lead to the need for replacement, the most common is the breakage of the lock, the other is the loss of the key.

Replacement of metal door door lockis made by selection of a similar type. If, of course, you can buy a similar model, then it will not be difficult to disassemble the door and install a new lock. Well, if the same castle could not be found, then there will be a little work. Locks of another model may have a larger larva size, and in this connection it is necessary to change the nest hole, which leads to small problems. The metal used to make metal structures is quite thick and durable, and this creates difficulties during drilling and cutting.

Features when replacing the lock

Replacement of the door lock of the metal door is made in order to increase the protection against burglaries with the use of protective fittings. Locking structure is used taking into account the thickness of the metal.

When making doors from metal placethe location of the lock is designed initially, and in this regard, the doors are already sold with the installed mechanism, which does not make it possible to change the already installed lock model to another. Typically, the locking mechanisms are different, and it is necessary to change the size of the new lock design. In this case, one can not do without a specialist, since reworking such a door is not a job for simpletons.

Replacement of the lock in the metal door with your own hands should be carried out in the following sequence:

- you need to find a lock that fits the door model;

- if the lock model does not fit, then it is necessary to make markings for the future lock;

- the lock is crashed and all locking mechanisms;

- the handle and overlays on both sides are installed;

- holes are drilled on the box to install bolts.

Locking device selection

Of the entire range offered today in thespecialized shops, for metal doors only mortise locks, that is, products with a body that can be mounted directly into the door leaf, can fit. Locks with a patch cover are very rarely used.

There are also electronic locks, but they require additional backup power, which leads to minor problems.

How to repair locks in a metal door

If an expensive mechanism is installed, the replacementlocks in a metal door will not be expensive, and to avoid unnecessary costs, it is wiser to buy a new one. Repair of such locks is considered a rather difficult work, since the replacement of individual elements requires time and money.

For example, replace the hardware, cylinder, secretdevices and other internal elements will be easier, as they can be purchased, but springs, gaskets and various washers and levers can not be replaced, because these parts are not sold as separate items. Also, the doors that were hacked by the barbaric method and whose mechanism was damaged are not subject to repair. Repair of metal doors, replacement of locks in products of Chinese production is impossible.

Self-replacement

This, of course, will require certain skills. Replacement of the door lock in the metal door with your own hands is made after its acquisition and horizontal marking. But first of all you need to decide on the lock and find out what mechanism is installed, also find out how many revolutions are closed, whether there is a heck and other details.

For marking from the end of the door measure the distancelocation of the castle. After carrying out horizontal lines, attaching the lock, it is necessary to mark the edges of the mechanism. For the accuracy of the markings, the thicknesser is used. To do this, dilute the parts of the thicknesser to the thickness of the lock itself and make a measurement. Then the markings are transferred to the front side of the door. It is important not to forget to mark the place where the well will be located, and make a mark between the vertically arranged lines.

Drilling

Also for a safe replacement mechanisma drill is selected which will allow the spindle in the hole to rotate freely. A through hole is drilled using a drill mounted on the faceplate. The same procedure is done on the reverse side. The well is cut in the same way. It is important to note that replacing locks in a metal door is a difficult process, since if you admit at least a small oversight, you can ruin the door.

Further, a recess for the body is made, for thisA drill of the required thickness is selected. To perform the extraction of the desired size, the size of the lock is measured and the markings are glued on the drill using an insulating tape. Using this drill, holes are made at several points where the body will be located and, using a hammer and a bit, perform a notch. In the resulting opening is placed body. The lock design is attached to the door by screws and screwed through special holes. Then the spindle is installed, the handle is inserted into place.

Replacement of the larva

If the locking structure and protective functionsarrange hosts, then a quick and inexpensive solution to problems will be the installation of a new larva. Replacement of the latch of the lock of the metal door can be made due to the loss of keys or their theft.

A new larva can even be installedamateur. To remove the old core, it is enough to unscrew the bolt, which is located just below the bolt. To detect it, it is necessary to examine the end part of the open door. After removing the fastening, the old core is removed. If it does not move, you need to insert the key and, turning it, remove the part.

After the core is removed, a new larva is installed. It is inserted in such a way that the hole where the bolt will be screwed is located in the center of the end face.

Installing the pen

Also replacement of locks in a metal doorincludes and the replacement of the pen. They have a different modification, depending on the model of the lock can be semi-automatic and standard. They are also divided into two types: right-handed and left-handed. The equipment includes an armored car, which protects the cylinder from mechanical damage. The principle of the semi-automatic handle is to close the doors without a key by lifting it from the outside to the top. If you push it down inside the apartment - the door opens.

Handles come in the following models:

- on the bar;

- on the bar under the key ring;

- on a separate basis.

Conclusion

To install the handle, you must mark the placeinstallation. Then the hole for the tongue of the handle is drilled. Apply the bar and note the holes through which the bolts will be fixed handle. After marking with a drill of the required diameter, a hole is drilled. After this, you need to insert the design into the door and fix it with bolts.

To date, there are firms thatthe locks in the metal door are replaced. The reviews showed that when people turned to specialists they received qualitative and quick help, since working with a metal door is not an easy task, and only a highly qualified specialist can handle it.