LED multicolor ribbon with control panel

Lighting devices are onstage of active development. Its main direction is the segment of technological Led-devices, in which new developments, design and design solutions appear regularly. Light-emitting diodes have been attracting the consumer for a wide range of advantages - from a high operational resource to an economical energy consumption.

Do not remain without attention and unique opticalproperties. In this regard, there are different opinions, because even a classical incandescent lamp in some cases of use proves to be a more advantageous solution. Nevertheless, the decorative qualities of such devices are not in doubt. It is these characteristics that optimally embodies the multi-color LED ribbon, which is often used as an element of design design.

General information about LED strips

Along with the spread of conventional Led-lamps,which already became traditional in themselves, the luminous contour bands gradually gained popularity. They were devoid of solid housings, but also had diodes in the composition. They were used to illuminate rooms or individual interior zones with the effect of masking. Also this option is used in those cases when it is not possible to provide uniform illumination in long rooms due to standard point devices.

In some way, the continuation of this concept andbecame a multi-color LED ribbon, which, in fact, has the same shape and assumes a similar installation method. However, the ability to use one light source in different color formats has formed a special niche for devices of this type. It is not just a decorative accessory for the house in the form of a bright backlight, but also a full-fledged attribute of the design of nightclubs, hotels and other establishments. The scope of use depends on the specific tape model and its capabilities.

How is the multi-color LED strip?

The ribbon itself is electrically conductivepaths and LED crystals, through which the user-defined glow dissipates. The main feature of such devices is the presence of an RGB-controller. This is a small unit, which is mounted separately, but it has a bundle with both the supply element and the diodes. Actually, it generates signals that provide the possibility of glowing with different shades.

Therefore, the tape is connected directly to fourwires - red, blue and green, and the fourth serves as a common power supply channel. But before the signal from the controller goes to the functional part, it will be processed by an infrared sensor. Directly to the network, a multicolor RGB LED strip is usually not connected. The power supply acts as a link, at the output transmitting a charge of 12 V.

Special modifications of tapes

Depending on the site of application,require a tape with some or other protective properties. For example, it can be moisture-proof, dustproof and hermetic modifications that can be used without the risk of premature failure of the diodes. To ensure protective qualities, special external coatings and shells are most often used - from composite inclusions to plastic membranes.

Fully sealed multi-color LEDThe tape is usually used for facades. With its help, illumination of shop windows, signboards, street decorative objects, etc. is provided. During operation, neither rain nor wind with snow can damage such a device. Also for protection against vandals, already as a separate option, manufacturers offer oblong cases with the possibility of light transmission. With the help of such additions, a barrier against mechanical damage is created.

Control system

One of the main advantagessuch tapes from the general segment of lighting devices, is the intellectual stuffing. For the user, this means programming with a wide range of functional solutions. Direct interaction with the device is carried out using the remote control (remote control). Already in the basic complete sets of LED multicolor ribbon with remote control gives the possibility of setting on this or that luminescence format.

On the compact control panel are locatedbasic color solutions, which can be selected by a single click of the user. In addition, through the same remote control panel, it is also possible to assign certain formats of the device operation - for example, to maintain a certain glow in a given time interval or to change colors at different intervals.

How to connect multi-color LED strip?

In the home organization of the lighting system, suchtapes are usually mounted according to the principles of hidden installation - as a rule, in the sub-ceiling niche. Mechanical installation will not cause problems, since the tape is enough to glue, and two auxiliary units are integrated with the help of complete fasteners. It only remains to connect the cord from the power supply to the outlet and you can use the system to the fullest.

However, an important aspect ofa bundle of the tape itself and the controller, which is implemented through the above four wires. For this task, it is desirable to use stranded 0.75 mm wires with a length of about 20 cm. In order for the multicolor LED strip to work correctly, it is necessary to accurately connect each antenna with a matching crystal using a soldering iron.

Operating modes of the belt

Already noted the main management capabilitiestape, but even with the purchase it will be superfluous to pay attention to the modes of operation from the point of view of the glow. The developers provide a whole set of different color combinations for different moods. In particular, there are bright glow modes, night, balanced, and also focused on background unobtrusive lighting. In addition, a multi-color LED strip with a control panel allows the user to customize individual radiation parameters. Thus, it is possible to create individual formats for the operation of the tape with the most appropriate backlighting.

Manufacturers

The market is mainly available productsChinese and Taiwanese manufacture. Nevertheless, it will not be difficult to find worthy solutions. Inexpensive, but quality options are offered under the brands Azkoti and Magna. If you need devices with a large working resource, then it makes sense to refer to the famous SMD series or to purchase models based on LEDX Radio controllers. If you need an option for street lighting, then the LED multicolor ribbon Magic Lights, which is positioned as a universal one, is suitable. However, and at a price this moisture-proof device in full complete with the power unit and controller will cost not cheap - about 2,5 thousand r.

Conclusion

The use of LED ribbons justifies itselffor different reasons. If you compare them with alternative solutions in the form of other types of illumination, then a wide spectrum of color spectrum of radiation, high brightness and a small consumption of energy resources will come to the fore. But even if you do not consider the operational properties, a multi-color LED tape can benefit from the ease of installation and reliability of the connection scheme. The introduction of a power supply and an infrared sensor in the chain not only increased the stability of the tape, but also benefited the user's interaction with the glow elements. But on the other hand, like all LED devices, this tape is quite expensive.