How to make a bracelet from a rope: a master class, step by step instructions and recommendations

Such a stylish accessory, like a bracelet, can be easily done by yourself, using only improvised tools. Consider the different types of these ornaments, the basis of which is the rope.

Simple bracelet made of twine

The usual twine, woven and put on the arm, can look very impressive. And to make such a bracelet from a rope is simple. It will take some time.

You can use, for example, the macrame method. To do this, take two pieces of not the most coarse twine length of about five meters, fold in half and fix the bend. It can be fastened with a pin, tape, press a book and so on. Then weave will become much easier.

The filaments are divided and knotted from external twinesby tying the central ones. And so repeat, each time shifting them over the central ones. While tightening the knots, you should pay attention to the central threads can not be seen.

Bracelet made of string with beads

How else to weave a bracelet out of a rope? Very nice looking decoration with beads. For him, take seven threads, the length of which is one and a half meters. Six pieces are collected and looped. And the seventh thread is tied with a loop on the side. Next, this thread is tied around the entire loop of six threads. At the end it is cut off and hidden.

Then six strands of string beadssize. At the same time, the largest of them should be located far apart from each other. After this, make a knot and again string the different beads. Again a node and so on. At the end thread one large bead, which will act as a fastener. One more accessory is ready.

Rope bracelet with decorative ring

An interesting option may be a braidedaccessory. As the main material is better to choose a bright thread of cotton, and an element of the decor will make a metal ring. From the consumables you will need glue and fasteners.

Take three strands, fold them twice, formingloop. This part will become a knot for the metal ring. To do this, a ring is threaded on one end of the rope, and the other end is passed through the loop and tightened. A similar knot is made on the other side of the ring. It should be a ring in the middle, with six threads stretching on each side of it.

Next, weave a pigtail with one, and then with the otherside. Having received a length sufficient for the bracelet, the excess ropes cut off, cauterize the ends, spread them with glue and insert the prepared fasteners. It remains to add a clasp - and a fashionable bracelet from the rope is ready.

Bracelet from a large rope

For this bracelet, take ropes, whose diameter is 5 millimeters, metal clasp and pliers. How to make a bracelet from a rope?

One rope is folded in half and forms a loop. Another rope is also folded and placed under the first loop. Then take a loop of the second rope, place it on the first loop and stretch it under the ends. The formed loop is laid on the beginning of the second rope, passing it under its ends. The resulting knot should be tightened evenly on both sides. From each side there must be loops and rope tips.

Try on the future bracelet, you need to cut off the big ends, set them on with a cigarette lighter and fasten them with fasteners on both sides. That's all. Strikingly light, but very stylish bracelet from the rope is ready.

About the bracelet "Shambhala"

This magical, as the supporters of religion assure,The bracelet is a unique source of energy. The effect is achieved by weaving two cords, inside which weave different beads. Those who want to learn how to weave bracelets from ropes "Shambhala" will need the following materials:

• board;
• cords waxed 3 meters long;
• glue;
• 10-15 beads;
• scissors;
• lighter.

Beads are better to pick different types. They can be both wooden and metal, from natural materials and precious stones. Also, the beads are selected from monochrome, variegated and of different colors. Even the form is different. And if round beads are selected, they symbolize peace of mind, tranquility and happiness. Cherepobraznaya form will protect from dangers, snakes will reveal the potential of dramatic changes in man, and beads-crosses will bring stability in life.

The cord is chosen in most cases from a synthetic rope. Suitable nylon or nylon, the diameter of which is almost two millimeters.

How to weave bracelets from ropes "Shambhala"

Having prepared everything you need, you can proceedweaving. To do this, take a board and nail to it two nails, one opposite the other. On one side, tie one end of the main rope, to which beads are strung. The other end is tied to the second clove. The thread must be stretched.

The second thread is doubled and tied higherthe first bead. The left part of it is passed under the main rope, and the top is put on the right rope, which is passed over the main rope and looped, tightening it. The same manipulations are alternately done on one side and then on the other. After 20 or more nodes have the first bead. Each of them is decomposed in an arbitrary order, but the basic scheme can be chosen as follows: 22 knots, a bead, 9 knots, another bead and then three beads and beads have three more times through the same number of knots. In the end, as in the beginning, make 22 knots.

Having finished the weaving, the bracelet is removed from the studs, knotted in addition a few ordinary knots and cut off the threads, having blurred the tips of the superglue. But the main rope is not cut off.

Fashionable and expressive bracelets

Rope bracelets can be made by handvery expressive. Take any bright rope, measure the diameter of the wrist and cut into five pieces, cauterize and fasten on one side with a clasp. Next, take a thread mulina one color range and braid all the pieces of the rope, moving perpendicular to their location. At the end of the work, the ropes are fixed on the other side.

Another simple way how to make a bracelet fromrope, the next. They take a bright rope of forty centimeters in length, a clasp with a crimp and a large wooden bead. The rope is cut into two parts and fixed one side together with the floss of the moulin. Then we twist both threads in such a way that they like, in the middle string the bead, add them to the end and fasten the fastener on the other side.