Origami "rose": assembly diagrams

It has long been no secret that in the technique of origami it is possibledo many different crafts. Flowers are no exception. We suggest you to find out how the origami rose is made in the technique. Assembly diagrams can be seen in the master classes below.

Flat Rose

Instructions how to assemble a simple rosette:

Take the colored paper and make a square from it.
Then bend the square in half to make a triangle.
Expand the sheet and place it as shown in Figure 1.
Wrap the left and right diamond tops to the fold line (Figure 2).
Unbend the edges of the wrapped sides in different directions, as in illustration 3.
Bend the figure in half, lifting the lower vertex upwards (Figure 4).
Step back from the bottom edge a few millimeters and bend the upper half (Figures 5 and 6).
Slightly wrap the "ears", as in illustration 7.
Then spread the "ears" and smooth them (Figures 8 and 9).
As a result, you will have a figure, as in Figure 10.
Fold the top of the figure and flip the part (illustration 11).
Take a square sheet of green paper and bend it in half (Figure 12).
Wrap its right and left sides to the fold line (Figure 13).
Turn the left and right sides again, as in illustration 14.
Bend the part in half in half.
Bend the part as shown in illustration 15.
Insert one part into the other.

You got a simple origami artwork - a rose.

Schemes of assembling a wreath from roses

The way to make a three-dimensional flower:

Take a sheet of colored paper and bend it two times in half parallel.
Turn the sheet and bend it in half, only on the other side.
Reinstate the sheet and flip it with the back side.
Now bend the sheet twice diagonally.
Unfold the sheet and lay it in front of you so that the diagonal fold lines are a convex side at the top.
Fold the sheet into a rhombus.
You have a workpiece in order to get a three-dimensional origami "rose". The diagrams for assembling this part for a flower and for a butterfly are the same.
Now wrap the left and right sides of the upper half of the diamond.
Flip the part.
Wrap the right and left sides of the second half.
Lower the top of the part down.
Now bend the top and sides of the figure.
Stretch them and fold the "boat".
Smooth the sides. You have a flat "boat".
Bend the figure in half by folding the top and bottom top together, and flip over.
Turn the item upside down.
Fold the shape first in half in length, then lower the bottom, then fold it diagonally.
On the resulting lines, fold a new shape. With tulips, this part of the origami scheme is similar. The roses are not ready yet.
Take the detail in one hand, and the other pull the edges of the figure to the sides. Open your flower. As a result, you will get a detail, as in the diagram.
Fold all four corners to the center and tighten them.
Spread the petals.

Make such roses very much, fasten them together and get the original wreath.

Compact Rosettes

Master class, how to make a rose of origami:

The assembly scheme is quite complicated. First you need to prepare a sheet of paper. To do this, fold it into the accordion diagonally on one side, then straighten it and do the same on the other.
Then put in front of you and wrap a little each corner (picture 1).
Slightly pull the left corner and fold it (pictures 2 and 3).
Do the same with the other corners (picture 4).
Then straighten the middle so that you can see an even square (picture 5).
Turn over the shape (picture 6).
Now add one side of the detail along the lines marked in Figures 7, 8 and 9.
Do the same with the other sides (picture 10).
Wrap the part as shown in pictures 11, 12 and 13.
Spread the rose.

Other Assembly Options

There are many variants of how the origami-rose is made. Schemes of some of them are presented above. For example, you can collect one flower head or a rose on the stem.

From ready-made crafts you can collect bouquets, make postcards, hairpins and much more.