"Interskol P-26 / 800ER" (puncher): specifications, user manual, repair, reviews

Before choosing a puncher, you need toDetermine what tasks will be put before the equipment. It is important to consider whether all the options are necessary for you. Some models offered for sale have very limited functions, which positively affects the cost. Some units have only one drilling mode, others - two: drilling and impact. If desired, you can purchase a punch with three modes, the previous two will be added and chiselling.

Features of choice

By weight, the perforators can be divided into lungs,heavy and with an average weight. The weight of the first does not exceed 4 kg, while the averages may have a mass within 5 kg. As for the heaviest instruments, their weight is sometimes 10 kg or more.

It is important to pay attention not only to the maina set of functions, but also a manufacturer, which should have a good reputation among consumers. Among others in a wide range in the market of construction equipment are perforators "Interskol". The P-26 / 800EP is one of the models of this supplier, it will be discussed below.

Model Description

This perforator has an acceptable cost -4600 rub. The model is capable of operating in one of three modes. Working attachments can be replaced almost instantly, this will help the cartridge SDS-plus. The puncher "Interskol P-26 / 800EP", about which you can read below, is characterized by safe operation. The operator during the use of the device will be reliably protected by a safety clutch if the tooling is blocked in the material.

Additionally, the manufacturer supplied the equipmentfunction of the reverse, it is represented by the rotation of carbon brushes. This contributes to a longer period of their operation and uniform power with versatile rotation. The set is complemented by a depth limiter, through which it is possible to drill holes with certain parameters.

Specifications

The puncher "Interskol P-26 / 800EP" weighs 2.9 kg. The power of the equipment is 780 W. You should consider that the device does not have a drilling chuck and vibration protection. Drill holes with concrete in this concrete with a drill, their diameter is 26 mm. If you use a crown, then with its help in the brick it will be possible to make holes with a maximum diameter of 68 mm. In the metal holes with this model of the perforator can be done with a diameter of up to 13 mm.

Additional features

This version of the equipment has an adjustmentspeed. The frequency of impacts varies from 0 to 5400 per minute. The puncher "Interskol P-26 / 800EP" has three modes of operation. The maximum impact force is 3 J. The length of the cable is equivalent to 4 m. In wood, the maximum drilling diameter is 30 mm. The design is equipped with a safety clutch. Some consumers and specialists are interested in the spindle speed parameter. It can vary from 0 to 1250 per minute.

Feedback on the main advantages

Consumers like the puncher "Interskol P-26 / 800EP" described in the article with the SDS-cartridge. This is due to a variety of reasons, among the main ones:

• functionality;
• high performance;
• modern design;
• turning the chisel;
• presence of a safety clutch;
• reverse;
• additional handle;
• depth limiter;
• case.

A simple change of tooling the consumer will be able toTo carry out with the help of cartridge SDS-plus. To protect the user and tool when the drill is jammed, the design is equipped with a safety clutch. For a reliable retention of the tool, you can use an additional handle, which the home masters consider very comfortable. In order to make blind holes, you can use the depth gauge.

Repair of puncher

Repair perforator "Interskol" canOnly after the expiry of the warranty period. The task of eliminating mechanical damages is more complicated than when the electronics fail. Immediately to establish the cause of the breakdown can be quite difficult. First, you should visually inspect all the details, and after the breakdown is identified - to fix the problem.

If you are faced with the fact that the deviceturns on, but does not break, then a broken switch could lead to a breakdown. The defective fingers of the switch may indicate a malfunction. They are constantly in contact with the rotating parts, this causes wear and tear. However, it sometimes happens that the fixing device fails, which keeps it in the gear housing. In this case, the mode starts to switch spontaneously.

If this problem does not bother you, then changeThe fixator is not necessary, because the punch will work. However, if you decide to repair the perforator "Interskol", you will need to replace the switch. If the suitable one was not found, and the work can not be stopped in any way, then the worn part can simply be turned by 180 ° C.

This approach will allow the work to continue. As for the cartridge, this part of the mechanism is subjected to the greatest loads, this sometimes becomes the cause of breakdowns. If you are faced with such a problem, then the cartridge must be simply replaced. Extend the service life by preventive maintenance: cleaning from dirt and washing with gasoline from dust.

Methods of work

The puncher "Interskol P-26 / 800EP 2" has a firing pin andcompressor ring. The failure of these elements can occur due to the impressive loads. If you are faced with a breakdown of this kind, then the only way out is to replace the node. When the reducer breaks down, it is first disassembled and checked for all the details. The most vulnerable place is the bearing. It must be checked for integrity. It should be replaced, if such a need arises. But the reason can also be covered in the seat. When it is produced, it starts to hold the bearing poorly. The body of the perforator in this case will have to be replaced.

Quite often they come into disrepairgears of a reducer. Having examined them visually, you can understand, whether so it. It is impossible to repair this part of the perforator, it will be necessary to replace it. The puncher "Interskol P-26 / 800EP 2" may encounter an oil leak. This happens very rarely. But if it does happen, then you only have to replace the stuffing box, which is located in the neck of the body. The work of the puncher can be intermittent and may get dirty. This is indicated by gnashing and crackling. In order to avoid such a problem, from time to time it is necessary to clean and lubricate the internal cavity of the perforator. It is important to use one type of lubricant, without changing it throughout the life of the device.

User's manual

The puncher "Interskol P-26 / 800EP" followstest by trial plug-in still in the store. The start of operation should be accompanied by a safety check of the workplace. It must be kept clean, it is important to ensure its good illumination. If the workplace has been poorly lit or cluttered, this can cause accidents.

An electric machine must neveroperate in an explosive atmosphere, under conditions that may include the presence of flammable dust, gases and liquids. This requirement is due to the fact that the operation of the device is accompanied by the generation of sparks, which can cause ignition of fumes or dust. Plug plugs should be ideally suited to sockets. They should not be changed on their own.

Manufacturer's recommendations

For machines with grounding wire is not recommendeduse adapters. It is important to exclude the effect of rain on the electric machine. It is not recommended to keep it in damp conditions. If moisture gets into the housing, then it can cause a person's electric damage. The described puncher for concrete has a power cord, which must be handled with care. Do not use it to drag the tool and remove the plug from the outlet. The following shall not be affected by an electrical device:

• sharp edges;
• butter;
• heat;
• moving parts.

The risk of electric shock is increased if the cord is twisted or damaged.

Safety measures when operating a perforator

Using a shock machine, you should usehearing protection. It is important to remember that doing work may lead to damage to the buried electrical wiring. This is why the tool must be held by insulated handles during operation.

If there is a contact with the wiring, it canlead to fire or electric shock to the operator. The concrete puncher should be used only after using a metal detector you will find hidden engineering networks like electric, steam, gas and water pipes. The additional handle must be used during operation. It is included. The puncher should be held with both hands, taking a stable position.

It is important to remember that the tool can jam,if its working parts fall into large fragments, stones or into the armature. For sudden jamming, the equipment will react with a backstab, this may cause loss of control of the device. If the tool jams, it must be immediately switched off. Release the puncher from the hands can only after the engine is completely stopped.

Service Features

Characteristics of the perforator "Interskol P-26 / 800EP2 »were presented above, however this information is not the only one that you should familiarize with if you decided to purchase such a model. The operator needs to know how the unit is serviced. Before starting such manipulations, it is necessary to remove the plug from the socket. For safe and high-quality work after the end of operation, it is necessary to clean the machine and the ventilation opening of dirt and dust. After use, clean the binding axle.

If you notice that when you turn on equipmentthere is no rotation, then a malfunction of the impactor or gearbox may indicate a similar problem. Sometimes it happens that the motor does not work when the device is turned on. It is important to check whether there is voltage in the network. A faulty plug or switch may cause this problem. Sometimes the power cord or wiring is cut off. If you hear increased noise in the impactor or gearbox, its parts may be worn or broken.

Cost of consumables and spare parts

If you needed a concrete drill forperforator, then you can buy it at a cost of 40 rubles. and higher. Prices vary depending on the size of the drill, parameters, quality of manufacture, the manufacturer. When choosing it is important to pay attention to the parameters. For example, a drill bit for concrete for the perforator of the following sizes, 6x160 mm, will cost the consumer from 48 rubles. If the dimensions are 10x1000 mm, then you can buy a drill from 400 rub.

No matter how high-quality the equipment is, itmay require replacement parts. For example, a button switch you can buy for 1260 rubles., While coal brushes will cost the consumer 450 rubles. Manufacturers advise to use the original spare parts for the perforator "Interskol P-26 / 800EP". Thus, the rolling clutch will cost the buyer 2,100 rubles. As for the case of the reducer, it can be bought for 1820 rubles. The piston shell costs 1,250 rubles, while the stator of the electric motor is 990 rubles. If you need to replace the anchor, you can buy it for 1390 rubles.

Conclusion

How to choose a puncher was conductedspeech above. However, it should be remembered that it is important to pay attention to some other peculiarities. For example, the impact energy. If you have a light model in front of you, the impact force of the perforator will be approximately 2 J, while the instruments of a more serious class are able to strike with force up to 15 J.

Choosing a puncher with more impact energy, youyou can provide the possibility of making holes with a larger diameter. For some consumers this feature is paramount. If this value is small, then the device will not work as efficiently.