How to check and replace the "Ford Focus 2" bearing?
Ford Focus 2 is very common in Russiacar. The car has a classic suspension scheme, where the front stand stands MacPherson. For their rotation, a support bearing is designed. "Ford Focus 2" does not cause problems with the operation, but to 150 thousand can get out of the bearings. For what they are needed, where they are and how to replace, we will consider in our today's article.
Characteristic
Support bearing "Ford Focus" 2nd generationIt serves to ensure that the shock absorber rotates freely in the upper support. When turning the wheels, it is important to avoid friction, which will cause increased wear and an increase in the temperature of the elements. The front bearing bearings of the "Ford Focus" 2nd generation allow to minimize the unfavorable factors and contribute to an easy, noiseless turn of the wheel.
Symptoms
How to check the bearing on the Ford Focus2nd generation? You can determine the malfunction without specialized equipment. Thus, with a worn bearing, there will be a distinct knocking sound in the area of the left or right side member. Especially it is strengthened when driving on irregularities and when turning the wheels.
The next sign is the controllability of the machine. If the bearing of the front pillar is worn out, the Ford Focus 2 will be less manoeuvrable on the road. The steering wheel will start to lyuftovat, there will be a skip during its rotation. In advanced cases, you will hear a crunch in the front of the body.
Causes of malfunction
Because of what this element can failon Ford Focus 2? The bearing is often broken due to natural wear. But there are a number of factors that can accelerate this process. So, first of all, a bad ride on bad roads is not welcome. Some motorists are guided by the rule "more speed - less pits", which is fundamentally wrong. The bearing will take even greater loads, since other suspension parts simply do not have time to work out a stroke normally.
Is it subject to repair?
Support bearing - a part that can not be lentrepair. It changes to a new one. However, to prolong the service life, it is possible to perform periodic prophylaxis. It consists in processing lithium grease inside the cage.
How to identify a malfunction in advance?
You can prevent this breakage in advance. This is especially important for those who are going on a long trip. So, first you need to open the hood and take hold of the shock absorber strut. Further it is necessary to shake it several times from side to side (in the place of its attachment to the body). If there is any play, then the element is unsuitable for operation. For a larger lever, you can shake the body by grasping the edge of the wing. So the body will "walk", and the rack will remain in place. This will also talk about the failure of the rack bearing.
Replacement
So, the suspicions were confirmed, and we bought a new onebearing. Note that the part does not need to be changed by a pair, as the racks themselves. In order to replace the support bearing on Ford Focus 2 successfully, we need a set of tools (heads and spanners), as well as an inspection pit or a hoist. On bare asphalt, you can do the work, but it will be very long and difficult.
First lift the front of the body jack. To hang out it is necessary from the side where there is a broken bearing with a rack. It will also be necessary to remove the wheel, having previously torn off the bolts. To avoid spontaneous movement (since the car front-drive and put "on the transfer" will be ineffective), set the stops back and pull the handle.
Now lightly unscrew the bolts that are boltedsupport bearing. "Ford Focus 2" continues to stand on the jack. Also note that the second "Ford" came with ABS. Therefore for replacement it is necessary to disconnect corresponding wires and gauges.
Next, open the clamp. It is necessary to prop up the fist of the wheel. We unscrew bolts of fastening of a rack and we remove it from the car. After dismantling, you can go to the very replacement of the bearing.
Dismantling and installation of the support bearing
First you need to clamp the rack in the vice, then - remove the spring. This is done with the help of several pullers that look like this.
When installing a new element, it is important not to confusehis position. On the Ford, the upper part of the support bearing has a protrusion. They need to turn the cup into a sloping side. The spindle is then placed in a special hole. Then rotate the swivel part of the bearing and put the stop limiter. The latter should be fixed with a latch. The stopper is installed with a thick end to the bearing.
Rack installation
So, the element is pressed into its place. Now it remains only to install the rack. When carrying out assembly work, make sure that the position of the spring is correct. Then the rack is assembled into the body cup. In order not to damage the thread, it is recommended to use a torque wrench. So, the moment of an inhaling of nuts of the basic bearing of a rack on "Ford Focus" of 2nd generation makes an order of 62 Nanometers.
Check the quality of work
After the replacement, you should check the reliabilityinstallation of the bearing. No break-in is required. In the first kilometers, sharp maneuvers are allowed by the rudder. So you can check the quality of the new bearing. The element should not make a crunching and grinding motion. To fully check the part, it is necessary to unscrew the rudder to the stop (of course, at low speeds).
Conclusion
So, we found out what the basicbearing and how to replace it with a Ford Focus second generation car. As you can see, all the work can be done by one's own hands. Among special tools it is necessary to highlight the couplers of springs (it will take at least two), a vice and a torque wrench. With these tools, you can quickly and easily replace the bearing of the shock absorber with your own hands.